Rule-base current control for Microgrid Energy Management System

Maher G.M. Abdolrasol, M. A. Hannan, Azah Mohamed

Research output: Contribution to journalArticle

Abstract

Rule-base current control for Microgrid Energy Management System (EMS) is an idea to managing different micro sources by using rule-base to allow each resource to participate in the Microgrid in prober time when needed. These resources are Photovoltaic (PV), wind turbine (WT), fuel cell (FC), and diesel generator and battery storage. Every source waits for a control signal from the rule-base controller to connect or disconnect from the Microgrid based on pre-prepared rule bases. Since this Microgrid needs a load, a real load data of 2MW has been collected and involved in the system. This load has been built by Matlab Simlink for 24 hours, wherein each hour was represented by 0.1Sec in the simulation and the power factor was 0.85. The controller has been tested in real residential and industrial load data taken from TNB in Selangor, Malaysia. Represented as Microgrid control signal for each source, rms current signal, and sinwave current signal, the results expressed controller's behavior when the current decreases and increases.
Original languageEnglish
Pages (from-to)125-128
Number of pages112
JournalJournal of Telecommunication, Electronic and Computer Engineering
Publication statusPublished - 01 Jan 2017
Externally publishedYes

Fingerprint

Energy management systems
Electric current control
Controllers
Fuel cells
Wind turbines

Cite this

@article{4f9d92c1e45148bfaa810d4a3f183a09,
title = "Rule-base current control for Microgrid Energy Management System",
abstract = "Rule-base current control for Microgrid Energy Management System (EMS) is an idea to managing different micro sources by using rule-base to allow each resource to participate in the Microgrid in prober time when needed. These resources are Photovoltaic (PV), wind turbine (WT), fuel cell (FC), and diesel generator and battery storage. Every source waits for a control signal from the rule-base controller to connect or disconnect from the Microgrid based on pre-prepared rule bases. Since this Microgrid needs a load, a real load data of 2MW has been collected and involved in the system. This load has been built by Matlab Simlink for 24 hours, wherein each hour was represented by 0.1Sec in the simulation and the power factor was 0.85. The controller has been tested in real residential and industrial load data taken from TNB in Selangor, Malaysia. Represented as Microgrid control signal for each source, rms current signal, and sinwave current signal, the results expressed controller's behavior when the current decreases and increases.",
author = "Abdolrasol, {Maher G.M.} and Hannan, {M. A.} and Azah Mohamed",
year = "2017",
month = "1",
day = "1",
language = "English",
pages = "125--128",
journal = "Journal of Telecommunication, Electronic and Computer Engineering",
issn = "2180-1843",
publisher = "Universiti Teknikal Malaysia Melaka",

}

Rule-base current control for Microgrid Energy Management System. / Abdolrasol, Maher G.M.; Hannan, M. A.; Mohamed, Azah.

In: Journal of Telecommunication, Electronic and Computer Engineering, 01.01.2017, p. 125-128.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Rule-base current control for Microgrid Energy Management System

AU - Abdolrasol, Maher G.M.

AU - Hannan, M. A.

AU - Mohamed, Azah

PY - 2017/1/1

Y1 - 2017/1/1

N2 - Rule-base current control for Microgrid Energy Management System (EMS) is an idea to managing different micro sources by using rule-base to allow each resource to participate in the Microgrid in prober time when needed. These resources are Photovoltaic (PV), wind turbine (WT), fuel cell (FC), and diesel generator and battery storage. Every source waits for a control signal from the rule-base controller to connect or disconnect from the Microgrid based on pre-prepared rule bases. Since this Microgrid needs a load, a real load data of 2MW has been collected and involved in the system. This load has been built by Matlab Simlink for 24 hours, wherein each hour was represented by 0.1Sec in the simulation and the power factor was 0.85. The controller has been tested in real residential and industrial load data taken from TNB in Selangor, Malaysia. Represented as Microgrid control signal for each source, rms current signal, and sinwave current signal, the results expressed controller's behavior when the current decreases and increases.

AB - Rule-base current control for Microgrid Energy Management System (EMS) is an idea to managing different micro sources by using rule-base to allow each resource to participate in the Microgrid in prober time when needed. These resources are Photovoltaic (PV), wind turbine (WT), fuel cell (FC), and diesel generator and battery storage. Every source waits for a control signal from the rule-base controller to connect or disconnect from the Microgrid based on pre-prepared rule bases. Since this Microgrid needs a load, a real load data of 2MW has been collected and involved in the system. This load has been built by Matlab Simlink for 24 hours, wherein each hour was represented by 0.1Sec in the simulation and the power factor was 0.85. The controller has been tested in real residential and industrial load data taken from TNB in Selangor, Malaysia. Represented as Microgrid control signal for each source, rms current signal, and sinwave current signal, the results expressed controller's behavior when the current decreases and increases.

UR - https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85020758405&origin=inward

UR - https://www.scopus.com/inward/citedby.uri?partnerID=HzOxMe3b&scp=85020758405&origin=inward

M3 - Article

SP - 125

EP - 128

JO - Journal of Telecommunication, Electronic and Computer Engineering

JF - Journal of Telecommunication, Electronic and Computer Engineering

SN - 2180-1843

ER -