Multi objective optimization of surface roughness and workpiece surface temperature in turning operation

Ahmad Nooraziah, Tiagrajah V. Janahiraman

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

This paper presents the optimization of multiple performance characteristics (surface roughness and workpiece surface temperature) based on the Taguchi method. Three controllable factors of the turning process were studied at three levels. The single objective optimization was conducted using Taguchi method. The multiple Signal-to-Noise (MSNR) value was used to correspond to multi objective cases. The optimum combination of cutting parameters was obtained based on the highest value of MSNR.

Original languageEnglish
Title of host publicationMechanical and Materials Engineering
PublisherTrans Tech Publications Ltd
Pages376-380
Number of pages5
Volume554
ISBN (Print)9783038351092
DOIs
Publication statusPublished - 2014

Publication series

NameApplied Mechanics and Materials
Volume554
ISSN (Print)1660-9336
ISSN (Electronic)1662-7482

Fingerprint

Taguchi methods
Multiobjective optimization
Surface roughness
Temperature

All Science Journal Classification (ASJC) codes

  • Engineering(all)

Cite this

Nooraziah, A., & V. Janahiraman, T. (2014). Multi objective optimization of surface roughness and workpiece surface temperature in turning operation. In Mechanical and Materials Engineering (Vol. 554, pp. 376-380). (Applied Mechanics and Materials; Vol. 554). Trans Tech Publications Ltd. https://doi.org/10.4028/www.scientific.net/AMM.554.376
Nooraziah, Ahmad ; V. Janahiraman, Tiagrajah. / Multi objective optimization of surface roughness and workpiece surface temperature in turning operation. Mechanical and Materials Engineering. Vol. 554 Trans Tech Publications Ltd, 2014. pp. 376-380 (Applied Mechanics and Materials).
@inproceedings{b531090d02c5469893ac80f9c05ee21c,
title = "Multi objective optimization of surface roughness and workpiece surface temperature in turning operation",
abstract = "This paper presents the optimization of multiple performance characteristics (surface roughness and workpiece surface temperature) based on the Taguchi method. Three controllable factors of the turning process were studied at three levels. The single objective optimization was conducted using Taguchi method. The multiple Signal-to-Noise (MSNR) value was used to correspond to multi objective cases. The optimum combination of cutting parameters was obtained based on the highest value of MSNR.",
author = "Ahmad Nooraziah and {V. Janahiraman}, Tiagrajah",
year = "2014",
doi = "10.4028/www.scientific.net/AMM.554.376",
language = "English",
isbn = "9783038351092",
volume = "554",
series = "Applied Mechanics and Materials",
publisher = "Trans Tech Publications Ltd",
pages = "376--380",
booktitle = "Mechanical and Materials Engineering",

}

Nooraziah, A & V. Janahiraman, T 2014, Multi objective optimization of surface roughness and workpiece surface temperature in turning operation. in Mechanical and Materials Engineering. vol. 554, Applied Mechanics and Materials, vol. 554, Trans Tech Publications Ltd, pp. 376-380. https://doi.org/10.4028/www.scientific.net/AMM.554.376

Multi objective optimization of surface roughness and workpiece surface temperature in turning operation. / Nooraziah, Ahmad; V. Janahiraman, Tiagrajah.

Mechanical and Materials Engineering. Vol. 554 Trans Tech Publications Ltd, 2014. p. 376-380 (Applied Mechanics and Materials; Vol. 554).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

TY - GEN

T1 - Multi objective optimization of surface roughness and workpiece surface temperature in turning operation

AU - Nooraziah, Ahmad

AU - V. Janahiraman, Tiagrajah

PY - 2014

Y1 - 2014

N2 - This paper presents the optimization of multiple performance characteristics (surface roughness and workpiece surface temperature) based on the Taguchi method. Three controllable factors of the turning process were studied at three levels. The single objective optimization was conducted using Taguchi method. The multiple Signal-to-Noise (MSNR) value was used to correspond to multi objective cases. The optimum combination of cutting parameters was obtained based on the highest value of MSNR.

AB - This paper presents the optimization of multiple performance characteristics (surface roughness and workpiece surface temperature) based on the Taguchi method. Three controllable factors of the turning process were studied at three levels. The single objective optimization was conducted using Taguchi method. The multiple Signal-to-Noise (MSNR) value was used to correspond to multi objective cases. The optimum combination of cutting parameters was obtained based on the highest value of MSNR.

UR - http://www.scopus.com/inward/record.url?scp=84903549298&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84903549298&partnerID=8YFLogxK

U2 - 10.4028/www.scientific.net/AMM.554.376

DO - 10.4028/www.scientific.net/AMM.554.376

M3 - Conference contribution

SN - 9783038351092

VL - 554

T3 - Applied Mechanics and Materials

SP - 376

EP - 380

BT - Mechanical and Materials Engineering

PB - Trans Tech Publications Ltd

ER -

Nooraziah A, V. Janahiraman T. Multi objective optimization of surface roughness and workpiece surface temperature in turning operation. In Mechanical and Materials Engineering. Vol. 554. Trans Tech Publications Ltd. 2014. p. 376-380. (Applied Mechanics and Materials). https://doi.org/10.4028/www.scientific.net/AMM.554.376