Mechanical and wear properties of aluminum coating prepared by cold spraying

Siti Nurul Akmal Yusof, Abreeza Noorlina Abd. Manap, Nurfanizan Mohd Afandi, Musdalilah Salim, Halina Misran

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)

Abstract

In this study, aluminum (Al) powders were deposited onto Al substrates using cold spray to form a coating. The main objective is to investigate and compare the microstructure, mechanical and wear properties of Al coating to that of the Al substrate. The microstructure of the coating and substrate were observed using Scanning Electron Microscope (SEM). Hardness was evaluated using the Vickers Hardness test and wear properties were investigated using a pin-on-disk wear test machine. The elemental composition of the coating and substrate was determined using Energy-dispersive X-ray spectroscopy (EDX). Results showed that the friction coefficient and specific wear rate decreased while wear rate increased linearly with increasing load. It was found that the coating exhibit slightly better mechanical and wear properties compared to the substrate.

Original languageEnglish
Title of host publicationProceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014
EditorsFauziah Othman, Aamir Hussain Bhat, Sujan Chowdhury, Norani Muti Binti Mohamed, Othman Bin Mamat, Patthi Bin Hussain
PublisherAmerican Institute of Physics Inc.
ISBN (Electronic)9780735413160
DOIs
Publication statusPublished - 22 Jul 2015
Event23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014 - Tronoh, Malaysia
Duration: 10 Dec 201412 Dec 2014

Publication series

NameAIP Conference Proceedings
Volume1669
ISSN (Print)0094-243X
ISSN (Electronic)1551-7616

Conference

Conference23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014
CountryMalaysia
CityTronoh
Period10/12/1412/12/14

Fingerprint

aluminum coatings
spraying
mechanical properties
coatings
aluminum
hardness tests
microstructure
Vickers hardness
wear tests
coefficient of friction
sprayers
hardness
electron microscopes
scanning
spectroscopy
x rays

All Science Journal Classification (ASJC) codes

  • Physics and Astronomy(all)

Cite this

Yusof, S. N. A., Abd. Manap, A. N., Mohd Afandi, N., Salim, M., & Misran, H. (2015). Mechanical and wear properties of aluminum coating prepared by cold spraying. In F. Othman, A. H. Bhat, S. Chowdhury, N. M. B. Mohamed, O. Bin Mamat, & P. Bin Hussain (Eds.), Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014 [4919182] (AIP Conference Proceedings; Vol. 1669). American Institute of Physics Inc.. https://doi.org/10.1063/1.4919182
Yusof, Siti Nurul Akmal ; Abd. Manap, Abreeza Noorlina ; Mohd Afandi, Nurfanizan ; Salim, Musdalilah ; Misran, Halina. / Mechanical and wear properties of aluminum coating prepared by cold spraying. Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014. editor / Fauziah Othman ; Aamir Hussain Bhat ; Sujan Chowdhury ; Norani Muti Binti Mohamed ; Othman Bin Mamat ; Patthi Bin Hussain. American Institute of Physics Inc., 2015. (AIP Conference Proceedings).
@inproceedings{ca74e62efb7d42939c2eb1a57d02b82c,
title = "Mechanical and wear properties of aluminum coating prepared by cold spraying",
abstract = "In this study, aluminum (Al) powders were deposited onto Al substrates using cold spray to form a coating. The main objective is to investigate and compare the microstructure, mechanical and wear properties of Al coating to that of the Al substrate. The microstructure of the coating and substrate were observed using Scanning Electron Microscope (SEM). Hardness was evaluated using the Vickers Hardness test and wear properties were investigated using a pin-on-disk wear test machine. The elemental composition of the coating and substrate was determined using Energy-dispersive X-ray spectroscopy (EDX). Results showed that the friction coefficient and specific wear rate decreased while wear rate increased linearly with increasing load. It was found that the coating exhibit slightly better mechanical and wear properties compared to the substrate.",
author = "Yusof, {Siti Nurul Akmal} and {Abd. Manap}, {Abreeza Noorlina} and {Mohd Afandi}, Nurfanizan and Musdalilah Salim and Halina Misran",
year = "2015",
month = "7",
day = "22",
doi = "10.1063/1.4919182",
language = "English",
series = "AIP Conference Proceedings",
publisher = "American Institute of Physics Inc.",
editor = "Fauziah Othman and Bhat, {Aamir Hussain} and Sujan Chowdhury and Mohamed, {Norani Muti Binti} and {Bin Mamat}, Othman and {Bin Hussain}, Patthi",
booktitle = "Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014",

}

Yusof, SNA, Abd. Manap, AN, Mohd Afandi, N, Salim, M & Misran, H 2015, Mechanical and wear properties of aluminum coating prepared by cold spraying. in F Othman, AH Bhat, S Chowdhury, NMB Mohamed, O Bin Mamat & P Bin Hussain (eds), Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014., 4919182, AIP Conference Proceedings, vol. 1669, American Institute of Physics Inc., 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014, Tronoh, Malaysia, 10/12/14. https://doi.org/10.1063/1.4919182

Mechanical and wear properties of aluminum coating prepared by cold spraying. / Yusof, Siti Nurul Akmal; Abd. Manap, Abreeza Noorlina; Mohd Afandi, Nurfanizan; Salim, Musdalilah; Misran, Halina.

Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014. ed. / Fauziah Othman; Aamir Hussain Bhat; Sujan Chowdhury; Norani Muti Binti Mohamed; Othman Bin Mamat; Patthi Bin Hussain. American Institute of Physics Inc., 2015. 4919182 (AIP Conference Proceedings; Vol. 1669).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

TY - GEN

T1 - Mechanical and wear properties of aluminum coating prepared by cold spraying

AU - Yusof, Siti Nurul Akmal

AU - Abd. Manap, Abreeza Noorlina

AU - Mohd Afandi, Nurfanizan

AU - Salim, Musdalilah

AU - Misran, Halina

PY - 2015/7/22

Y1 - 2015/7/22

N2 - In this study, aluminum (Al) powders were deposited onto Al substrates using cold spray to form a coating. The main objective is to investigate and compare the microstructure, mechanical and wear properties of Al coating to that of the Al substrate. The microstructure of the coating and substrate were observed using Scanning Electron Microscope (SEM). Hardness was evaluated using the Vickers Hardness test and wear properties were investigated using a pin-on-disk wear test machine. The elemental composition of the coating and substrate was determined using Energy-dispersive X-ray spectroscopy (EDX). Results showed that the friction coefficient and specific wear rate decreased while wear rate increased linearly with increasing load. It was found that the coating exhibit slightly better mechanical and wear properties compared to the substrate.

AB - In this study, aluminum (Al) powders were deposited onto Al substrates using cold spray to form a coating. The main objective is to investigate and compare the microstructure, mechanical and wear properties of Al coating to that of the Al substrate. The microstructure of the coating and substrate were observed using Scanning Electron Microscope (SEM). Hardness was evaluated using the Vickers Hardness test and wear properties were investigated using a pin-on-disk wear test machine. The elemental composition of the coating and substrate was determined using Energy-dispersive X-ray spectroscopy (EDX). Results showed that the friction coefficient and specific wear rate decreased while wear rate increased linearly with increasing load. It was found that the coating exhibit slightly better mechanical and wear properties compared to the substrate.

UR - http://www.scopus.com/inward/record.url?scp=85063858373&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85063858373&partnerID=8YFLogxK

U2 - 10.1063/1.4919182

DO - 10.1063/1.4919182

M3 - Conference contribution

T3 - AIP Conference Proceedings

BT - Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014

A2 - Othman, Fauziah

A2 - Bhat, Aamir Hussain

A2 - Chowdhury, Sujan

A2 - Mohamed, Norani Muti Binti

A2 - Bin Mamat, Othman

A2 - Bin Hussain, Patthi

PB - American Institute of Physics Inc.

ER -

Yusof SNA, Abd. Manap AN, Mohd Afandi N, Salim M, Misran H. Mechanical and wear properties of aluminum coating prepared by cold spraying. In Othman F, Bhat AH, Chowdhury S, Mohamed NMB, Bin Mamat O, Bin Hussain P, editors, Proceedings of the 23rd Scientific Conference of Microscopy Society Malaysia, SCMSM 2014. American Institute of Physics Inc. 2015. 4919182. (AIP Conference Proceedings). https://doi.org/10.1063/1.4919182