Effect of lubricant content to the properties of Fe-based components formed at above ambient temperature

Md Mujibur Rahman, S. S.M. Nor, A. K. Ariffin

Research output: Contribution to journalConference article

4 Citations (Scopus)

Abstract

This paper presents the outcomes of an experimental investigation on the effect of lubricant content to the mechanical properties and microstructure of components formed at above ambient temperature. A lab-scale uni-axial die compaction rig was designed and fabricated which enabled the powder forming at elevated temperature. Iron powder ASC 100.29 was mechanically mixed with different quantity of lubricant, i.e., zinc stearate for 10, 30, and 60 minutes, respectively. Green compacts were generated by forming the prepared powder mass at 180°C through simultaneous upward and downward axial loading. The defect-free green compacts were subsequently sintered in argon gas fired furnace and characterized for their physical and mechanical properties as well as their microstructures were evaluated. The results revealed that the characteristics of final products were affected by lubricant content and mixing time. From this study, the suitable zinc stearate content and mixing time were identified for the production of high quality components through warm forming route.

Original languageEnglish
Pages (from-to)425-430
Number of pages6
JournalProcedia Engineering
Volume68
DOIs
Publication statusPublished - 01 Jan 2013
Event2013 1st Malaysian International Tribology Conference, MITC 2013 - Kota Kinabalu, Sabah, Malaysia
Duration: 18 Nov 201320 Nov 2013

Fingerprint

Lubricants
Zinc
Powders
Mechanical properties
Iron powder
Microstructure
Temperature
Argon
Furnaces
Compaction
Physical properties
Defects
Gases

All Science Journal Classification (ASJC) codes

  • Engineering(all)

Cite this

@article{1bd19320d93241cf9d81423e5ab8c258,
title = "Effect of lubricant content to the properties of Fe-based components formed at above ambient temperature",
abstract = "This paper presents the outcomes of an experimental investigation on the effect of lubricant content to the mechanical properties and microstructure of components formed at above ambient temperature. A lab-scale uni-axial die compaction rig was designed and fabricated which enabled the powder forming at elevated temperature. Iron powder ASC 100.29 was mechanically mixed with different quantity of lubricant, i.e., zinc stearate for 10, 30, and 60 minutes, respectively. Green compacts were generated by forming the prepared powder mass at 180°C through simultaneous upward and downward axial loading. The defect-free green compacts were subsequently sintered in argon gas fired furnace and characterized for their physical and mechanical properties as well as their microstructures were evaluated. The results revealed that the characteristics of final products were affected by lubricant content and mixing time. From this study, the suitable zinc stearate content and mixing time were identified for the production of high quality components through warm forming route.",
author = "Rahman, {Md Mujibur} and Nor, {S. S.M.} and Ariffin, {A. K.}",
year = "2013",
month = "1",
day = "1",
doi = "10.1016/j.proeng.2013.12.202",
language = "English",
volume = "68",
pages = "425--430",
journal = "Procedia Engineering",
issn = "1877-7058",
publisher = "Elsevier BV",

}

Effect of lubricant content to the properties of Fe-based components formed at above ambient temperature. / Rahman, Md Mujibur; Nor, S. S.M.; Ariffin, A. K.

In: Procedia Engineering, Vol. 68, 01.01.2013, p. 425-430.

Research output: Contribution to journalConference article

TY - JOUR

T1 - Effect of lubricant content to the properties of Fe-based components formed at above ambient temperature

AU - Rahman, Md Mujibur

AU - Nor, S. S.M.

AU - Ariffin, A. K.

PY - 2013/1/1

Y1 - 2013/1/1

N2 - This paper presents the outcomes of an experimental investigation on the effect of lubricant content to the mechanical properties and microstructure of components formed at above ambient temperature. A lab-scale uni-axial die compaction rig was designed and fabricated which enabled the powder forming at elevated temperature. Iron powder ASC 100.29 was mechanically mixed with different quantity of lubricant, i.e., zinc stearate for 10, 30, and 60 minutes, respectively. Green compacts were generated by forming the prepared powder mass at 180°C through simultaneous upward and downward axial loading. The defect-free green compacts were subsequently sintered in argon gas fired furnace and characterized for their physical and mechanical properties as well as their microstructures were evaluated. The results revealed that the characteristics of final products were affected by lubricant content and mixing time. From this study, the suitable zinc stearate content and mixing time were identified for the production of high quality components through warm forming route.

AB - This paper presents the outcomes of an experimental investigation on the effect of lubricant content to the mechanical properties and microstructure of components formed at above ambient temperature. A lab-scale uni-axial die compaction rig was designed and fabricated which enabled the powder forming at elevated temperature. Iron powder ASC 100.29 was mechanically mixed with different quantity of lubricant, i.e., zinc stearate for 10, 30, and 60 minutes, respectively. Green compacts were generated by forming the prepared powder mass at 180°C through simultaneous upward and downward axial loading. The defect-free green compacts were subsequently sintered in argon gas fired furnace and characterized for their physical and mechanical properties as well as their microstructures were evaluated. The results revealed that the characteristics of final products were affected by lubricant content and mixing time. From this study, the suitable zinc stearate content and mixing time were identified for the production of high quality components through warm forming route.

UR - http://www.scopus.com/inward/record.url?scp=84899497292&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84899497292&partnerID=8YFLogxK

U2 - 10.1016/j.proeng.2013.12.202

DO - 10.1016/j.proeng.2013.12.202

M3 - Conference article

VL - 68

SP - 425

EP - 430

JO - Procedia Engineering

JF - Procedia Engineering

SN - 1877-7058

ER -